reorder
ALWAYS Be Happy search home
c
Combo Blog
Categories
Play Games New
Food Serving Equipment,Coffee & Hot Beverage Dispensers
STANTON TRADING

Bell Creamer 5oz Stainless Steel

About The STANTON TRADING 4475 Bell Creamer 5oz Stainless Steel

STANTON TRADING 4475 Bell Creamer 5oz Stainless Steel

Food Serving Equipment,Coffee & Hot Beverage Dispensers

Bell Creamer 5oz Stainless Steel

Food Serving Equipment,Coffee & Hot Beverage Dispensers

Specifications of Bell Creamer 5oz Stainless Steel

Category
Instockinstock

Last Updated

Bell Creamer 5oz Stainless Steel
More Varieties

Rating :- 9.79 /10
Votes :- 18
1/2 Diameter x 1/2 Shank 2-Flute Extra Long Length Ball Nose Yellow Series Carbide End Mills

1/2 Diameter x 1/2 Shank 2-Flute Extra Long Length Ball Nose Yellow Series Carbide End Mills

These end mills have the capability to mill much thicker material in a single pass, thereby eliminating the interrupted cut that may be present with regular length end mills Extra Long Length End mills combine added flute and overall length for greater reach when deep slotting or milling.

  • Cutting Tools,End Mills,Ball 2-Flute End Mills
  • GS TOOLING
    • - Steel sealed for coolant through applications - Pressure resistance tested to 2000 psi
  • Machining,Collets,Chucks & Accessories,Collets
  • GS TOOLING
    • Type ER Collet Series ER40 Hand or Pipe Tap Hand Through Coolant No Tap Size Metric M20 For synchronous, rigid tapping operations using ER collet chuck Collet bore is exact tool diameter with square drive for accuracy and rigidity
  • Machining,Collets,Chucks & Accessories,Collets
  • GS TOOLING
    • Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 114 Projection Decimal Inch 394 Nose Diameter Decimal Inch 173 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market

    Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 114 Projection Decimal Inch 394 Nose Diameter Decimal Inch 173 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market

    CAT50 114 x 394 Shrink Fit Holder With Coolant Ports.

  • Cutting Tools,Indexable Tools,Indexable Toolholders
  • GS TOOLING
    • Lathe Swing Inch 1420 Base Width Inch 4 All working parts hardened and ground Maximum rigidity for chatterfree performance No time wasted with shims Speed up your Lathe operations 90 Completely sealed for maintenancefree operation
  • Workholding & Machine Tool Accessories,Tool Posts
  • STM
    • TARPS NOW ICISC-1206-C Industrial Curtain with Clear Window-12' H X 6'

    TARPS NOW ICISC-1206-C Industrial Curtain with Clear Window-12' H X 6'

    Industrial Curtain with Clear Window-12' H X 6' W-CEILING MOUNT KIT.

  • Dock & Warehouse Equipment,Dock Gates & Doors,Curtain Walls
  • TARPS NOW
    • STANTON TRADING 4475 Bell Creamer 5oz Stainless Steel
  • Food Serving Equipment,Coffee & Hot Beverage Dispensers
  • STANTON TRADING
    • Plastic Tubing PUN-H-6X1-TGN

    Plastic Tubing PUN-H-6X1-TGN

    Bending Radius=10 Mm, Tubing Characteristics=Suitable For Energy Chains In Applications With High Cycle Rates Plastic Tubing Pun-H-6X1-Tgn Approved For Use In Food Processing (Hydrolysis Resistant) Outside Diameter=6 Mm, Bending Radius Relevant For Flow Rate=26 Mm, Inside Diameter=4 Mm, Min..

  • Compressors,Air Tanks & Pneumatic Parts,Air Hoses,Pneumatic Tubing
  • FESTO
    • STANTON TRADING 4475 Bell Creamer 5oz Stainless Steel
  • Food Serving Equipment,Coffee & Hot Beverage Dispensers
  • STANTON TRADING
    • Plastic Tubing PUN-H-6X1-TGN

    Plastic Tubing PUN-H-6X1-TGN

    Bending Radius=10 Mm, Tubing Characteristics=Suitable For Energy Chains In Applications With High Cycle Rates Plastic Tubing Pun-H-6X1-Tgn Approved For Use In Food Processing (Hydrolysis Resistant) Outside Diameter=6 Mm, Bending Radius Relevant For Flow Rate=26 Mm, Inside Diameter=4 Mm, Min..

  • Compressors,Air Tanks & Pneumatic Parts,Air Hoses,Pneumatic Tubing
  • FESTO