reorder
ALWAYS Be Happy search home
c
Combo Blog
Categories
Play Games New
Compressors,Air Tanks & Pneumatic Parts,Air Hoses,Pneumatic Tubing
FESTO

Plastic Tubing PUN-H-6X1-TGN

About The Bending Radius=10 Mm, Tubing Characteristics=Suitable For Energy Chains In Applications With High Cycle Rates.Plastic Tubing Pun-H-6X1-Tgn Approved For Use In Food Processing (Hydrolysis Resistant) Outside Diameter=6 Mm, Bending Radius Relevant For Flow Rate=26 Mm, Inside Diameter=4 Mm, Min

Plastic Tubing Pun-H-6X1-Tgn Approved For Use In Food Processing (Hydrolysis Resistant) Outside Diameter=6 Mm, Bending Radius Relevant For Flow Rate=26 Mm, Inside Diameter=4 Mm, Min. Bending Radius=10 Mm, Tubing Characteristics=Suitable For Energy Chains In Applications With High Cycle Rates

Compressors,Air Tanks & Pneumatic Parts,Air Hoses,Pneumatic Tubing

Plastic Tubing PUN-H-6X1-TGN

Compressors,Air Tanks & Pneumatic Parts,Air Hoses,Pneumatic Tubing

Specifications of Plastic Tubing PUN-H-6X1-TGN

Category
Instockinstock

Last Updated

Plastic Tubing PUN-H-6X1-TGN
More Varieties

Rating :- 9.95 /10
Votes :- 18
Type ER Collet Series ER40 Hand or Pipe Tap Hand Through Coolant No Tap Size Metric M20 For synchronous, rigid tapping operations using ER collet chuck Collet bore is exact tool diameter with square drive for accuracy and rigidity
  • Machining,Collets,Chucks & Accessories,Collets
  • GS TOOLING
    • Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 114 Projection Decimal Inch 394 Nose Diameter Decimal Inch 173 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market

    Shank Type Taper Shank Taper Size CAT50 Hole Diameter Inch 114 Projection Decimal Inch 394 Nose Diameter Decimal Inch 173 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market

    CAT50 114 x 394 Shrink Fit Holder With Coolant Ports.

  • Cutting Tools,Indexable Tools,Indexable Toolholders
  • GS TOOLING
    • Lathe Swing Inch 1420 Base Width Inch 4 All working parts hardened and ground Maximum rigidity for chatterfree performance No time wasted with shims Speed up your Lathe operations 90 Completely sealed for maintenancefree operation
  • Workholding & Machine Tool Accessories,Tool Posts
  • STM
    • TARPS NOW ICISC-1206-C Industrial Curtain with Clear Window-12' H X 6'

    TARPS NOW ICISC-1206-C Industrial Curtain with Clear Window-12' H X 6'

    Industrial Curtain with Clear Window-12' H X 6' W-CEILING MOUNT KIT.

  • Dock & Warehouse Equipment,Dock Gates & Doors,Curtain Walls
  • TARPS NOW
    • TARPS NOW ICISC-1206-C Industrial Curtain with Clear Window-12' H X 6'

    TARPS NOW ICISC-1206-C Industrial Curtain with Clear Window-12' H X 6'

    Industrial Curtain with Clear Window-12' H X 6' W-CEILING MOUNT KIT.

  • Dock & Warehouse Equipment,Dock Gates & Doors,Curtain Walls
  • TARPS NOW