reorder
ALWAYS Be Happy search home
c
Combo Blog
Categories
Play Games New
Door Hardware & Components,Door Locks and Deadbolts,Door Knob Locksets
SURE-LOC HARDWARE

Sure-Loc Hardware Bergen Square Entry Knobset, Flat Black

About The SURE-LOC HARDWARE BG107-SQ FBL Sure-Loc Hardware Bergen Square Entry Knobset,

SURE-LOC HARDWARE BG107-SQ FBL Sure-Loc Hardware Bergen Square Entry Knobset,

Door Hardware & Components,Door Locks and Deadbolts,Door Knob Locksets

Sure-Loc Hardware Bergen Square Entry Knobset, Flat Black

Door Hardware & Components,Door Locks and Deadbolts,Door Knob Locksets

Specifications of Sure-Loc Hardware Bergen Square Entry Knobset, Flat Black

Category
Instockinstock

Last Updated

Sure-Loc Hardware Bergen Square Entry Knobset, Flat Black
More Varieties

Sure-Loc Hardware Bergen Square Entry Knobset, Flat Black
Rating :- 9.58 /10
Votes :- 17
5007684 ICombi Hardware Kit

5007684 ICombi Hardware Kit

5007684 ICombi Hardware Kit.

  • Food Serving Equipment,Food Service Appliance Parts
  • ALTO-SHAAM
    • Thera-Band„¢ Exercise Mat, 24 x 75 x 0.6, Green

    Thera-Band„¢ Exercise Mat, 24 x 75 x 0.6, Green

    They also include pre-drilled hanging holes and two elastic straps for easy storage options.

  • Sports Equipment & Recreation,Exercise Equipment
  • FABRICATION ENTERPRISES
    • Boot; Gearshift,

    Boot; Gearshift,

    Boot; Gearshift 8" x3" x8".

  • Tractor Parts & Implements,Tractor Transmission & Rear Axle Parts
  • A & I PRODUCTS
    • Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 14 Projection Decimal Inch 630 Nose Diameter Decimal Inch 083 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market

    Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 14 Projection Decimal Inch 630 Nose Diameter Decimal Inch 083 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market

    HSK63A 14 x 630 Shrink Fit Holder With Coolant Ports.

  • Cutting Tools,Indexable Tools,Indexable Toolholders
  • GS TOOLING
    • Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 14 Projection Decimal Inch 630 Nose Diameter Decimal Inch 083 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market

    Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 14 Projection Decimal Inch 630 Nose Diameter Decimal Inch 083 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market

    HSK63A 14 x 630 Shrink Fit Holder With Coolant Ports.

  • Cutting Tools,Indexable Tools,Indexable Toolholders
  • GS TOOLING