reorder
ALWAYS Be Happy search home
c
Combo Blog
Categories
Play Games New
Machining,Collets,Chucks & Accessories,Machine Chucks
STM

400-500mm Rectangular Soft Top Jaw With Inch Serration Piece - 90mm Height, 3PK

About The 5For AutoBlok, Erickson, Forkardt, Gamet, Powerhold, Pratt Burnerd, Rohm and Howa Ho12M-Self Contained Air.Jaw Type: Square Material: Steel Jaw Interface Type: 3/32x90 degree Maximum Compatible Chuck Diameter mm: 500 Minimum Compatible Chuck Diameter mm: 400 Overall Height mm: 90 Groove Width mm: 25

Jaw Type: Square Material: Steel Jaw Interface Type: 3/32x90 degree Maximum Compatible Chuck Diameter mm: 500 Minimum Compatible Chuck Diameter mm: 400 Overall Height mm: 90 Groove Width mm: 25.5For AutoBlok, Erickson, Forkardt, Gamet, Powerhold, Pratt Burnerd, Rohm and Howa Ho12M-Self Contained Air

Machining,Collets,Chucks & Accessories,Machine Chucks

400-500mm Rectangular Soft Top Jaw With Inch Serration Piece - 90mm Height, 3PK

Shank Type Taper Shank Taper Size HSK63A Hole Diameter Inch 34 Projection Decimal Inch 394 Nose Diameter Decimal Inch 13 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market
Collet System ER Collet Series ER32 Shank Type Taper Shank Taper Size CAT50 Projection Decimal Inch 4 DIN Coolant option standard All Ground Body Factory Balanced to save spindle life, tool life and increased productivity Threaded through holes for a backup screw tool stop or coolant through when removed Wrench not included Premium balanced to G25 At 30,000 rpm
More from STM, Jaw Type: Square Material: Steel Jaw Interface Type: 3/32x90 Degree Maximum Compatible Chuck Diameter Mm: 500 Minimum Compatible Chuck Diameter Mm: 400 Overall Height Mm: 90 Groove Width Mm: 25.5For AutoBlok, Erickson, Forkardt, Gamet, Powerhold, Pratt Burnerd, Rohm And Howa Ho12M-Self Contained Air
Search

Machining,Collets,Chucks & Accessories,Machine Chucks

Specifications of 400-500mm Rectangular Soft Top Jaw With Inch Serration Piece - 90mm Height, 3PK

Category
Instockinstock

Last Updated

400-500mm Rectangular Soft Top Jaw With Inch Serration Piece - 90mm Height, 3PK
More Varieties

Rating :- 9.34 /10
Votes :- 21
Head Diameter Inch 316 Number of Flutes 1 Included Angle 100 Countersink Material Cobalt Countersink FinishCoating TiN Coated Shank Diameter Inch 316 Made from premium M42, 8 cobalt HSS Excellent for countersinking abrasive, highstrength, heat resistant, exotic and other difficult to machine materials TiN coated for higher surface hardness and better lubricity to enhance productivity and longer tool life
  • Cutting Tools,Countersinks,Center Drills & Spotting Drills,Countersinks
  • STM
    • 3/8 Dia x 3/8 Shank 0.020 Radius 4-Flute Reg Length Corner Radius Blue Series Carbide End Mills

    3/8 Dia x 3/8 Shank 0.020 Radius 4-Flute Reg Length Corner Radius Blue Series Carbide End Mills

    Four flute construction provides more strength than two or three flute and will also result in excellent surface finishes. Four flute carbide end mills with corner radius allows more strength and minimizes chipping on corners.

  • Cutting Tools,End Mills,Corner Radius 4-Flute End Mills
  • GS TOOLING
    • Type ER Collet Series ER40 Hand or Pipe Tap Hand Through Coolant No Tap Size Metric M10 For synchronous, rigid tapping operations using ER collet chuck Collet bore is exact tool diameter with square drive for accuracy and rigidity
  • Machining,Collets,Chucks & Accessories,Collets
  • GS TOOLING
    • 5/8 Diameter x 5/8 Shank 4-Flute Regular Length Typhoon Red Series Carbide End Mills

    5/8 Diameter x 5/8 Shank 4-Flute Regular Length Typhoon Red Series Carbide End Mills

    .The unique geometry of the Typhoon end mill combined with its modified AlTiN coating make it an excellent choice for demanding applications These end mills are manufactured with Premium Sub-Micron carbide and are designed to cut hardened materials.

  • Cutting Tools,End Mills,Carbide 4-Flute End Mills
  • GS TOOLING
    • 5/8 Diameter x 5/8 Shank 4-Flute Regular Length Typhoon Red Series Carbide End Mills
  • Cutting Tools,End Mills,Carbide 4-Flute End Mills
  • GS TOOLING