reorder
ALWAYS Be Happy search home
c
Combo Blog
Categories
Play Games New
Compressors,Air Tanks & Pneumatic Parts,Pneumatic System Components,Air Cylinders
FESTO

Compact Cylinder DPDM-Q-25-25-PA

About The Compact Cylinder Dpdm-Q-25-25-Pa Stroke=25 Mm, Piston Diameter=25 Mm, Cushioning=P: Flexible Cushioning Rings/Plates At Both Ends, Assembly Position=Any, Mode Of Operation=Double-Acting

Compact Cylinder Dpdm-Q-25-25-Pa Stroke=25 Mm, Piston Diameter=25 Mm, Cushioning=P: Flexible Cushioning Rings/Plates At Both Ends, Assembly Position=Any, Mode Of Operation=Double-Acting

Compressors,Air Tanks & Pneumatic Parts,Pneumatic System Components,Air Cylinders

Compact Cylinder DPDM-Q-25-25-PA

Compact Cylinder Adngf-100-25-Pps-A Stroke=25 Mm, Piston Diameter=100 Mm, Based On The Standard=Iso 21287, Cushioning=Pps: Self-Adjusting Pneumatic End-Position Cushioning, Assembly Position=Any
Shank Type Taper Shank Taper Size HSK63A Hole Diameter mm 10 Projection mm 85 Nose Diameter mm 24 Through Coolant Yes Unsurpassed Accuracy Concentricity of Less than or equal too00001 3 Micron with tool shrunk in holder Coolant Ports Each holder has 4 coolant ports in the nose to ensure coolant gets right to the tool Max Gripping Torque Tool is gripped 360Deg along the entire length of bore producing very high gripping torque, preventing chatter Increased Production Decrease down time the total time elapsed to remove one cutting tool and insert another is less than 10 seconds Balanced GS follows the strictest balance standards Our holders are prebalanced G25 up to 30,000rpm Extended Holder Life With double tempered tool steel construction, reduced centrifugal forces, minimized bore contamination, and minimized chatter, a GS Shrink Fit Toolholder should far outlast a standard end mill holder Chip load distributed evenly along cutting edge of tool which results in longer tool life Short projections are possible because no mechanical clamping devices are used This results in greater rigidity and resistance to bending Since Shrink Fit toolholders have no moving parts they offer the greatest repeatability of any tool holding system on the market
More from Compact Cylinder Dpdm-Q-25-25-Pa Stroke=25 Mm, Piston Diameter=25 Mm, Cushioning=P: Flexible Cushioning Rings/Plates At Both Ends, Assembly Position=Any, Mode Of Operation=Double-Acting - FESTO
Search

Compressors,Air Tanks & Pneumatic Parts,Pneumatic System Components,Air Cylinders

Specifications of Compact Cylinder DPDM-Q-25-25-PA

Category
Instockinstock

Last Updated

Compact Cylinder DPDM-Q-25-25-PA
More Varieties

Rating :- 9.93 /10
Votes :- 21
Drill Size Inch 118 Drill Material High Speed Steel FinishCoating Bronze Oxide Overall Length Inch 1234 Shank Type Taper Shank Used to open out existing predrilled holes 118Deg notched point 4 flute
  • Cutting Tools,Drill Bits,Core Drill Bits
  • STM PREMIUM
    • Drill Bit Size Inch 218 Shank Taper Designation MT4 Drill Point Angle Degrees 118 Drill Bit Material High Speed Steel Drill Bit FinishCoating Black Oxide Overall Length Inch 1614 Through Coolant No
  • Cutting Tools,Drill Bits,Taper Shank Drill Bits
  • STM PREMIUM
    • Reamer Blank Diameter Letter F Overall Length Inch 418 Made from hardened HRC 6365 high speed steel and ground, can be used as punches, gauges, pins or ground for special tools High Speed Steel 00000 0 00003
  • Cutting Tools,Tool Blanks,Reamer Blanks
  • STM PREMIUM
    • Mill Diameter Inch 12 End Type Corner Radius Corner Radius Decimal Inch 0005 Number of Flutes 3 Material Solid Carbide FinishCoating TiCN Length of Cut Inch 112 Shank Diameter Inch 12 Overall Length Inch 4 Cutting Direction Right Variable Index No Special geometry allows for high chip loads and feed rates 3 flute design excellent for slotting and profiling at high speeds Made from premium submicron grain carbide Cutting diameter tolerance 00000002
  • Cutting Tools,End Mills,Carbide End Mills
  • SOWA HIGH PERFORMANCE CUTTING TOOLS
    • Mill Diameter Inch 12 End Type Corner Radius Corner Radius Decimal Inch 0005 Number of Flutes 3 Material Solid Carbide FinishCoating TiCN Length of Cut Inch 112 Shank Diameter Inch 12 Overall Length Inch 4 Cutting Direction Right Variable Index No Special geometry allows for high chip loads and feed rates 3 flute design excellent for slotting and profiling at high speeds Made from premium submicron grain carbide Cutting diameter tolerance 00000002
  • Cutting Tools,End Mills,Carbide End Mills
  • SOWA HIGH PERFORMANCE CUTTING TOOLS